Turbo Kit Accessories


Page 1



 GT35R Dual Ball Bearing Turbo

 

Garrett/Precision GT35R Turbo. 

 

Comes standard with our Stage II or Stage III turbo systems.  Capable of flowing over 600hp, this dual ball bearing turbo comes with a 3“ inlet TO4E housing and 3“  4-bolt exhaust outlet with an .82 housing for a responsive all around street turbo setup. 

 

GT35R Turbo $1299.00 

 24"x12"x3" Turbo Intercooler

 

CES 24"x12"x3" Custom Turbo Intercooler for E36 BMW.  

 

Capable of flowing over 800 whp with 3“ inlet and outlet pipes that are bead rolled to prevent slippage, this EMC design intercooler was laser scanned to fit perfectly behind the M3 stock bumper.  Angled inlet and outlet pipes optimize air flow for maximum power gains.  Comes with all the necessary brackets and hardware for a bolt on fit. 

 

$1000.00  (you must trim your front metal bumper to fit this intercooler)

 
 High Flow Turbo Air Mass Meter

 

High Flow Air Mass Meter for E36 BMW.  

 

Used in all our Stage II and Stage III Turbo Systems, this meter allows for greater air volume to be measured by the stock ECU that the factory meter cannot handle. 

 

$399.00 (requires performance software upgrade on stock ECU)


 

OBD II air mass meter wiring kit (required for '96-'99 OBDII cars) $30.00

 MLS .140" Lower Compression Head Gasket

 

 

MLS .140“ lower compression turbo head gasket. E36 BMW. 

 

Brings the stock compression of 10:5:1 on M3 motors down to a more manageable  9:1 compression ratio.  A must when trying to boost over 9 psi using pump fuel on a stock motor. 

 

$229.00  



  


 AA BOV

 

Active Autowerke Blow Off Valve. 

 

Used to keep boost pressures from causing damage to the turbo compressor wheel when the throttle closes shut.  Has an adjustable spring to tighten or loosen bov tension.  Comes with gasket and fastening hardware 

 

$199.00                           

 CES Turbo Oil Distribution Kit

 

CES Turbo Oil Distribution Kit.

 

Frustrated trying to find the best way to feed your turbo oil?  We have made it easy with our turbo oil feed kit.  Bolts directly in between the oil sending unit of your E36 BMW.  Is  tee-d off with either a    –3 or –4 an fitting and comes with 48“ of  either   –3 or –4  stainless steel braided line.  -3 or -4 can be used with dual bb turbos that require oil restrictors. We recommend  -4 for non bb or single bb turbos.  

 

$69.00  -3 turbo oil dist. kit

$75.00  -4 turbo oil dist. kit
 CES Turbo 3" Intake Elbow

 


CES Turbo Intake Elbow E36 BMW


We offer both high quality polished t304 stainless steel, or 16G polished Aluminum versions of our elbow... It has a 3“ diameter that dramatically increases air flow when compared to other competitor’s cast elbows, bead rolled edges to keep silicone couplers from slipping, and an integrated bung on the bottom to use a fitting which can connect to factory plumbing. 

 

Direct factory replacement will withstand high levels of boost pressure.  Excellent replacement for factory rubber elbow and a must for turbo or other higher boost applications. 

 

Polished T304 Stainless Steel Elbow $75.00

 

16G Polished Aluminum Elbow $65.00

 

(requires fitting that screws in underneath the elbow to connect it to stock plumbing. ) Add $8.00
 Tial 44mm Turbo Wastegate

 

 

Tial 44 mm wastegate. 

 

V-banded connections make this a perfect choice for our turbo kits.  Larger 44 mm design regulates boost pressures much more accurately than smaller units.  Bolts up directly to our E36 BMW Turbo Downpipe and Re-route pipe kit via integrated v-band connections for quick installation or removal. 

 

$399.00